Hey everyone,
I'm looking at wiring up 3 gauges (Air Fuel Ratio, Oil Pressure, and one other), and possibly another lighting accessory which will all need a constant 12v circuit.
Is it possible to wire them all into the 12V accessory socket? Or should I wire them in a different place, like the radio power? Or will I have to wire each 12V accessory to a different 12v power source?
Unsure what I can and can't do. I still want to use the 12V accessory socket as normal for USB stuff.
Any insight would be greatly appreciated.
Running multiple 12v accessories off one power source?
Moderator: Moderators
Forum rules
This area is dedicated to technical discussions concerning in-car electronics. Stereos, alarms, GPS etc. Please try to spell correctly because this will help people find information later if they are using search functionality. If you need assistance with your car and want to host a spanner day, please use the appropriate section of the forum: http://mr2.org.nz/phpbb3/viewforum.php?f=35 Thank you.
This area is dedicated to technical discussions concerning in-car electronics. Stereos, alarms, GPS etc. Please try to spell correctly because this will help people find information later if they are using search functionality. If you need assistance with your car and want to host a spanner day, please use the appropriate section of the forum: http://mr2.org.nz/phpbb3/viewforum.php?f=35 Thank you.
- GlanzaAtHeart
- Club Member - MR2OCNZ
- Posts: 234
- Joined: Sun Oct 21, 2018 7:21 pm
- Stomping Ground: Auckland
- Prime Mover: SW20
- First name: Thomas
Running multiple 12v accessories off one power source?
89' SW20 GT w/ Gen 4 3SGTE
13.2 @ 107mph
"man this thing drives like ass" - Sun Tzu, probably
13.2 @ 107mph
"man this thing drives like ass" - Sun Tzu, probably
- Mr-Paulio
- Area Coordinator - MR2OCNZ
- Posts: 1284
- Joined: Sat Sep 06, 2014 6:48 am
- Stomping Ground: Auckland
- Prime Mover: AW11
- First name: Paul
Re: Running multiple 12v accessories off one power source?
You can run as many accessories as you want off one circuit as long as the total current of all those items isn't more than the fuse for the circuit. And you can't just put a bigger fuse in as the fuse protects the wiring from melting under high load. And you don't want more melted wiring aye?
So just total up the running amps of each. If its new they should be supplied with that data. If not you might have to mesure them when on.
Hope that helps
So just total up the running amps of each. If its new they should be supplied with that data. If not you might have to mesure them when on.
Hope that helps
'89 AW11 V6 Turbo (350BHP & 380Ft/lbs!)
'86 AW11 20V (Sold)
'91 SW20 Turbo "BlackRat" #RatRodStyle (Sold)
'91 SW20 Turbo (Sold)
South Auckland Area Coordinator
'86 AW11 20V (Sold)
'91 SW20 Turbo "BlackRat" #RatRodStyle (Sold)
'91 SW20 Turbo (Sold)
South Auckland Area Coordinator
- GDII
- Forum Moderator - MR2OCNZ
- Posts: 5792
- Joined: Sun Jul 10, 2011 5:13 pm
- Stomping Ground: Wellington
- Prime Mover: SW20
- First name: Phill
Re: Running multiple 12v accessories off one power source?
What he said!
1990 SW20 MR2 G-Limited (GEN4 3SGTE Installed)
2000 AE111R Corolla Wagon NZ New Daily
1996 AE101R Corolla Sprint NZ New Selling Soon
1990 EP81 Starlet XL (Sold)
1990 EE90 Corolla XL (Sold)
Instagram https://www.instagram.com/sw20glimited/
2000 AE111R Corolla Wagon NZ New Daily
1996 AE101R Corolla Sprint NZ New Selling Soon
1990 EP81 Starlet XL (Sold)
1990 EE90 Corolla XL (Sold)
Instagram https://www.instagram.com/sw20glimited/
- GlanzaAtHeart
- Club Member - MR2OCNZ
- Posts: 234
- Joined: Sun Oct 21, 2018 7:21 pm
- Stomping Ground: Auckland
- Prime Mover: SW20
- First name: Thomas
Re: Running multiple 12v accessories off one power source?
Oh please no more melted wiring, especially under the dashboardMr-Paulio wrote: ↑Fri Oct 09, 2020 11:06 pmYou can run as many accessories as you want off one circuit as long as the total current of all those items isn't more than the fuse for the circuit. And you can't just put a bigger fuse in as the fuse protects the wiring from melting under high load. And you don't want more melted wiring aye?
So just total up the running amps of each. If its new they should be supplied with that data. If not you might have to mesure them when on.
Hope that helps
Oh okay, so I would be safe, provided that the accessories I'm wiring in aren't overdoing it in terms of current draw. All but 1 of the accessories are new, but one of them isn't provided with an amp draw.
Would I just be best off running a secondary power wire from the battery, like car stereo amp wiring kits in most cars? Get one of those for ~ $30 and then use the power wire with an inline fuse? Probably the best way to do it now that I see that the wires behind the 12V socket aren't exactly thick. Just gotta figure out how i'd run it from there to only turn on when the car is running.
Thanks for the help - Didn't know it was only current that is the killer!
89' SW20 GT w/ Gen 4 3SGTE
13.2 @ 107mph
"man this thing drives like ass" - Sun Tzu, probably
13.2 @ 107mph
"man this thing drives like ass" - Sun Tzu, probably
- Benckj
- Forum Moderator - MR2OCNZ
- Posts: 7150
- Joined: Thu Nov 24, 2005 12:44 pm
- Stomping Ground: Otago
- Prime Mover: More than one MR2
- First name: Jim
Re: Running multiple 12v accessories off one power source?
What you need is a standard 12v 20amp relay. They will have 4 pins;
1/ Battery power +12v
2/ Ground
3/ Trigger ( use 12v that comes on with ignition like cig plug )
4/ 12v supply to all your accessories.
Make sure you install an in-line fuse to the 12 v supply rated to your wire gauge. I’m sure Phil can post up a link and pics on hi to do.
1/ Battery power +12v
2/ Ground
3/ Trigger ( use 12v that comes on with ignition like cig plug )
4/ 12v supply to all your accessories.
Make sure you install an in-line fuse to the 12 v supply rated to your wire gauge. I’m sure Phil can post up a link and pics on hi to do.
Jim Benck
90 rev 1 parts car
98 rev 5 GT- all the mods
90 rev 1 parts car
98 rev 5 GT- all the mods
- GlanzaAtHeart
- Club Member - MR2OCNZ
- Posts: 234
- Joined: Sun Oct 21, 2018 7:21 pm
- Stomping Ground: Auckland
- Prime Mover: SW20
- First name: Thomas
Re: Running multiple 12v accessories off one power source?
Ahh doing some research, this is perfect! Thank you!Benckj wrote: ↑Sat Oct 10, 2020 12:02 pmWhat you need is a standard 12v 20amp relay. They will have 4 pins;
1/ Battery power +12v
2/ Ground
3/ Trigger ( use 12v that comes on with ignition like cig plug )
4/ 12v supply to all your accessories.
Make sure you install an in-line fuse to the 12 v supply rated to your wire gauge. I’m sure Phil can post up a link and pics on hi to do.
Something like this will be exactly what I need.
I have some supercheap auto credit too, so I'll get one of these: https://www.supercheapauto.co.nz/p/trid ... CN01060705
I'm sure I can figure out how to wire it all up - Phil has been helping me more than enough already
Thanks Jim, this has been a huge help.
I'll post up some pics in the next week or so when I get all wired up.
One last quesiton however, the trigger - I presume I splice into the positive 12v source of the ciggarette lighter?
89' SW20 GT w/ Gen 4 3SGTE
13.2 @ 107mph
"man this thing drives like ass" - Sun Tzu, probably
13.2 @ 107mph
"man this thing drives like ass" - Sun Tzu, probably
- Benckj
- Forum Moderator - MR2OCNZ
- Posts: 7150
- Joined: Thu Nov 24, 2005 12:44 pm
- Stomping Ground: Otago
- Prime Mover: More than one MR2
- First name: Jim
Re: Running multiple 12v accessories off one power source?
Yes, that will work fine. Never seen one with a fuse included with relay. Hooking trigger to cig lighter is fine as I’m pretty sure this is energised with ACC rather than IGN. Just depends on what you want as can always pick a fused supply in kick panel to use. Just make sure you get a couple of insulated spade connectors to terminate into relay.
Jim Benck
90 rev 1 parts car
98 rev 5 GT- all the mods
90 rev 1 parts car
98 rev 5 GT- all the mods
- GlanzaAtHeart
- Club Member - MR2OCNZ
- Posts: 234
- Joined: Sun Oct 21, 2018 7:21 pm
- Stomping Ground: Auckland
- Prime Mover: SW20
- First name: Thomas
Re: Running multiple 12v accessories off one power source?
Yeah female spade connectors will probably be the go. I might solder in the 12V supply to the accessories as I might wire in a few.Benckj wrote: ↑Sat Oct 10, 2020 6:12 pmYes, that will work fine. Never seen one with a fuse included with relay. Hooking trigger to cig lighter is fine as I’m pretty sure this is energised with ACC rather than IGN. Just depends on what you want as can always pick a fused supply in kick panel to use. Just make sure you get a couple of insulated spade connectors to terminate into relay.
Thanks for the advice Appreciate it! Answered all my questions perfectly
89' SW20 GT w/ Gen 4 3SGTE
13.2 @ 107mph
"man this thing drives like ass" - Sun Tzu, probably
13.2 @ 107mph
"man this thing drives like ass" - Sun Tzu, probably